• Disk drive cage or StorageWorks™ shelf (Step 5)
• Disk drive cage (BA610-6D) requires mandatory selection of Ultra2 SCSI LVD storage adapter (3X-KZPCA-AA)
• StorageWorks shelf requires UltraSCSI adapter and SCSI cable (Step 10)

• System disk drive (Step 5)

• Ethernet adapter (Step 7)

• Tower, Pedestal, or Rack Kit (Step 8)

• Non-North American systems require country-specific keyboard (Step 16); North American systems include U.S. English keyboard

• One CPU included, three additional CPUs are supported

• Systems include one memory option; maximum 16 GB Model 1 and 32 GB Model 2 (see Notes below)

• Memory performance considerations: Interleaved operations reduce the average latency and increase the memory throughput over non-interleaved operations. With one memory option (4 DIMMs) installed, memory interleaving will not occur. With two identical memory options (8 DIMMs) installed, memory read-write operations are two-way interleaved. With four identical memory options (16 DIMMs) installed, memory read-write operations are four-way interleaved, maximizing memory throughput.

The patch to support greater than 2-GB of memory per system is located at:
http://www.kernel.org/pub/linux/kernel/people/
andrea/patches/v2.2/2.2.17 (patch name: bigmem-2.2.18pre2-18.bz2)
The following minimum operating system versions require the patch:

• Linux RedHat V6.2
• Linux SuSE V6.3 (Kernel V2.2.17)
  

Use this floppy when prompted by the install procedure for a floppy.

• One power supply supports two CPUs, up to 12 memory DIMMs, and one disk card cage; order second power supply if N+1 power is required.

• Two power supplies support third and fourth CPU, 13 to 32 memory DIMMs (up to 24-GB of memory), and/or two disk card cages; order third power supply if N+1 power is required for third and fourth CPUs, 24-GB of memory, and/or two disk card cages.

• Three power supplies support 32-GB of memory without N+1 power.

• Three power supplies support a maximum of 24-GB of memory with N+1 power.

• Each additional power supply ordered with a tower system requires an additional country-specific power cord

• Pedestal systems and Rack kit include three internal power cords regardless of the number of power supplies ordered.

• Tower enclosure supports one system and two disk drive cages

• Pedestal enclosure supports one system and two disk drive cages, two Universal 43xx StorageWorks shelves or three BA36R StorageWorks shelves

• M-Series cabinets support five systems each with two disk drive cages and up to six StorageWorks shelves

• Disk drive cage supports six 1.0² Universal disk drives per cage

• StorageWorks Shelf supports seven 3.5² x 1.6² hard disk drives; with addition of redundant power supply, only six drives are supported

• StorageWorks shelf kits are mounted back-to-back in pedestals and cabinets

DS-SL13R-AA
(All regions except Japan)

190209-291
(U.S./Canada orders
for Japan variant)

DS-SL13R-AJ
(Non U.S./Canada orders for Japan variant))

DS-SL13R-BA
(All regions except Japan)

190211-291
(U.S./Canada orders for Japan variant)

DS-SL13R-BJ
(Non U.S./Canada orders for Japan variant)

• System supports four internal removable devices

• System includes 1.44-MB diskette drive

• System includes 5.25² half-height 600-MB 40X IDE CD-ROM

• Removable media slots provide support for two 5.25² half-height devices, or one 5.25² full-height removable media device

• Each adapter uses one PCI slot

• Tower enclosure supports one system

• Tower enclosure ordered in North America includes 120V power cord; country-specific power cord mandatory for all non-North American systems; additional power cord mandatory for each power supply ordered with a system installed in a tower enclosure

BA61M-MT

• Pedestal enclosure supports one system, two Universal 43xx StorageWorks shelves (Universal shelves require onsite installation) or three UltraSCSI BA36R StorageWorks shelves

• Pedestal enclosures (BA61P-PA, 120V/BA61P-PB, 240V) support Universal shelves

• 120V pedestal enclosure includes two external 120V power cords; 240V pedestal enclosure requires two country-specific power cords

• Rack kit required for each AlphaServer ES40 system installed in a new or existing M-Series Cabinet

• Rack kit supports one system

BA61R-RM

• H9A10 or H9A15 cabinet, 120V or 240V

• Rack kit for each system

• H9A10 or H9A15 rear cabinet extender

• Cabinet front door based on cabinet height

• Factory integration

• Ballast kit if only one system is ordered for the H9A15 cabinet

1. Contact Compaq CustomSystems for cabinet configurations with four ES40 systems installed in an H9C10-MC/MD cabinet.
2. Japan only – 240V cabinet required when using universal shelves
3. When using a combination of BA356 and DS-SL13R shelves in cabinet, do not remove top fan, only remove fan when using
   DS-SL13R shelves exclusively (Universal shelves require onsite installation).
4. Installation of one AlphaServer ES40 system in an H9A15 cabinet requires the mandatory selection of a ballast kit.
5. When adding the 5^th system drawer, replace H7600-AA or -DB power controller with H7602-EA or -DB power controller. When replacing H7600 controllers, replace all associated power cords; order BN35S-4E power cords for H7602-EA and H7602-DB power controllers.

• Two H7600-xx power distribution units are standard in the M-series cabinet

• For cabinet configurations that require a third power distribution unit (H7600-xx), contact Compaq CustomSystems at 1-800-AT-COMPAQ

• Select graphics adapter, monitor, and country-specific keyboard if required

• Graphics monitors other than those listed can be used if compatible with SVGA graphics ordered with system

• At least one video cable, 6-foot/1.8-m length, is included with all variants of monitors.

• Video extension cable required if monitor is located more than 1 meter from server

• Monitors will ship with, but not be integrated with systems.

• Select a keyboard and mouse
• Order country-specific keyboard or mouse only if required
• All keyboards listed may not be available in all geographies

• Tower enclosure ordered in North America includes 120V power cord; selection of country-specific power cord is mandatory for all non-North American orders.

• Each additional power supply ordered with a system installed in tower enclosure requires an additional power cord

• Pedestal systems ordered in North America include two 120V power cords; selection of two country-specific power cords is mandatory for all non-North American orders.

• Any terminal can be used as a console device

• Third-party console devices require an EIA-232 25-pin DSUB connector