• Operating System support: HP UX 11i version 1 and HP UX 11i version 2 for HP 9000
• Dual channel Ultra320 LVD SCSI controller
• Two external Ultra320 LVD SCSI ports
• Two 10/100/1000Base T LAN ports (with auto speed sensing; RJ 45 connector)
• iLO Manageability Processor for remote management and HA monitoring
• Telnet and web console via 10/100Base-TX management LAN (RJ-45 connector)
• Three RS-232 serial ports linked to the management processor
• Factory integration of processors, memory, disk drives, removable media, and I/O cards
• Rackmountable into 19 inch cabinets - HP Rack System/E and HP Universal G2 1000 series as well as many 3rd party racks
• Optional stand-alone pedestal mount
• Three-year warranty with next business day on-site

• One two core PA 8900 processor module either 800 MHz/3 MB level 1 cache or 1 GHz/3 MB level 1 cache One 16 DIMM slot memory carrier board
  
• One hot swap power supply

• Four two core PA 8900 processor modules: Either 800 MHz/3 MB level 1 cache or 1 GHz/3 MB level 1 cache
  
• 128 GB PC2100 ECC Registered DDR266A/B SDRAM (32×2GB DIMMs)
  
• One 32 DIMM slot memory carrier board
  
• Two hot swap power supplies, providing N+1 protection for power supplies and power input
  
• 6 PCI X IO adapter cards
  
• One internal DVD-R (Read Only) or DVD+RW (Read/Write) optical drive
  
• Two internal hot plug LVD SCSI disks

• Operating System support: HP UX 11i version 1 and HP UX 11i version 2 for HP 9000
  
• Dual channel Ultra320 LVD SCSI controller
  
• Two external Ultra320 LVD SCSI ports
  
• Two 10/100/1000Base T LAN ports (with auto speed sensing; RJ 45 connector)
  
• iLO Manageability Processor for remote management and HA monitoring
  
• Telnet and web console via 10/100Base-TX management LAN (RJ-45 connector)
  
• Three RS-232 serial ports linked to the management processor
  
• Factory integration of processors, memory, disk drives, removable media, and I/O cards
  
• Rackmountable into 19 inch cabinets - HP Rack System/E and HP Universal G2 1000 series as well as many 3rd party racks
  
• Optional stand-alone pedestal mount
  
• Three-year warranty with next business day on-site

• N+1 Hotswap cooling
  
• One Hotswap power supply-optional second power supply for N+1 protection
  
• Hot Plug PCI-X I/O slots
  
• On-line memory page deallocation
  
• ECC protected DDR memory
  
• Memory chip spare to overcome single DRAM chip failures
  
• Dynamic Processor resilience and deallocation
  
• UPS power management
  
• Hot Plug internal disks
  
• Optional two channel Ultra320 SCSI RAID controller for mirroring across internal disks
  
• Journal file system with HP UX
  
• Auto reboot
  
• HP Serviceguard for HP-UX
  
• HP Serviceguard Extension for RAC for HP-UX
  
• HP Serviceguard Extension for SAP for HP-UX
  
• Serviceguard Manager for HP-UX Clusters
  
• HP Event Monitoring Service
  
• HA Monitors for HP-UX
  
• HA Toolkits for HP-UX Linux
  
• HP Mirrordisk/UX
  
• Extended Campus Cluster, HP Metrocluster, and HP Continentalclusters for HP-UX

• Separate LAN for system management
  
• Password protection on console port
  
• Disablement of remote console ports
  
• SSL encryption on web console

• HP Ignite-UX for installation and deployment of the operating system
  
• HP Software Distributor UX for software and patch management
  
• HP Integrity Essentials Foundation Pack for Windows including Smart Setup DVD

• Built in iLO Manageability Processor for comprehensive remote server management of HP UX,
  
• HP Servicecontrol suite for HP UX servers including tools for system administration, asset management, and fault management
  
• HP-UX kernel configuration for easy, dynamic kernel parameter changes

• Process Resource Manager for HP-UX resource management
  
• HP-UX Workload Manager for HP-UX workload management based upon service level objectives
  
• HP OpenView Glanceplus Pack

• Two core PA 8900 processor modules at 800 MHz or 1.0 GHz frequencies:
  
  • Level 2 Cache: 64 MB (shared between cores)
    
  • Level 1 Cache: 1.5 MB per core (3 MB per processor module)
    
  • Single bit cache error correction
    
  • 44 bit physical addressing
    
  • 64 bit virtual addressing
    
  • 4 GB maximum page size

• Two core processor modules can be installed one at a time
  
• Processors must be installed in the following sequence: 0, 1, 2, 3
  
• 800 MHz and 1.0 GHz processors cannot be mixed in the same system

The HP 9000 rp4440 supports double data rate (DDR) synchronous dynamic random access memory (SDRAM) DIMMs with ECC and chip spare protection. The HP 9000 rp4440 can be ordered with one of the following two memory carrier boards:

• A9738B-Supports from 4 to 16 DIMMs (1 to 64 GB); 12.8 GB/s memory bandwidth
  
• A9739B-Supports from 4 to 32 DIMMs (1 to 128 GB); 12.8 GB/s memory bandwidth

Both memory carrier boards provide the same bandwidth to the processors. The primary difference between the two boards is in total memory capacity.

• Memory must be installed in groups of four DIMMs, also known as quads
  
• Each quad must consist of equal density DIMMs
  
• Memory can be ordered in quads of 1 GB (4×256MB), 2 GB (4×512MB), 4 GB (4×1GB), 8 GB (4×2GB), or 16 GB (4x4GB)
• Minimum memory is 1 GB (4×256 MB)
  
• Maximum memory is 128 GB, using eight 16 GB memory quads in memory carrier board A9739B
  
• Memory must be loaded in the order depicted on the memory carrier board
  
• Arrange DIMMs so that the quads with the largest capacity are in the lowest numbered slots

The HP 9000 rp4440 can be installed in the field with the Field Rack Kit (A6977A). This field kit contains the slide mounts, cable management arm, and all other hardware needed to mount an rp4440 into a 19 inch cabinet.

Refer to the 10000 G2 Series Rack Best Practices Guide for information on rack deployment, stabilization and transportation. Go to HP.com/go/rackandpower for more information.

For stand alone, non racked deployments, the HP 9000 rp4440 can be placed into a freestanding tubular frame that wraps around the server (A6979A). This product is not available with factory installation. However, the tubular frame is easily installed in the field.

The HP 9000 rp4440 I/O architecture utilizes industry standard PCI X buses in a unique design for maximum performance, scalability and reliability.

The HP 9000 rp4440 architecture uses eight high speed I/O channels. Each channel provides 0.5 GB/s of sustained I/O throughput. The diagram above shows how these channels are used to provide bandwidth to the six available PCI X slots, two reserved PCI X slots, and to multifunction core I/O. The reserved slots, #1 and #2 (counting from the bottom) will always be filled with core I/O. Slot #2 will come factory loaded with a dual channel Ultra320 SCSI card. Slot #1 will come factory loaded with a two port 10/100/1000Base TX LAN adapter.

Each channel of the Ultra320 or Ultra160 SCSI card may be used for either internal or external connection but not both internal and external connections. The factory default configuration is one channel connected to the internal hard disk drive backplane. The second channel is free for use with an external tape drive or disk shelf (JBOD). The internal disk drives can be set up in a duplex configuration such that each disk has a dedicated SCSI channel. This is called a duplex configuration and is done to enhance server availability. It is often combined with disk mirroring software. The second internal SCSI cable is already in place to support a duplex configuration. Order A9740B for additional components needed on the SCSI backplane of the internal disks for duplex mode. Factory installation is recommended for the A9740B duplex kit.

The factory loaded dual channel Ultra320 SCSI card may be upgraded to a Smart Array 6402 Ultra320 RAID controller (A9890A) with support for internal hardware RAID1. When upgrading to Smart Array 6402, you must order all of the following:
1. Option 001 of base server
2. Two identical hard disk drives
3. Factory Express services

The two slots at the outside edge of the backplane (slots #7 & #8) each have their own dedicated 64 bit 133 MHz PCI X bus and their own independent 1.0 GB/s I/O channel. These slots should be used for high performance PCI and PCI X cards, such as clustering interconnects or multi port storage adapters. The independent buses and I/O channels provide improved performance and error containment. Independence protects each I/O card from bus hangs or extended latencies due to the failure or high bandwidth demands of other I/O cards. Independence also ensures that each I/O card can achieve maximum throughput. Both of these slots support hot plug operations in HP UX. Hot plug is not supported with the Linux operating system.

The remaining four slots (#3 through #6) share two 64 bit 66 MHz PCI X buses, with two slots allocated to each bus. Each pair of slots shares a 0.5 GB/s I/O channel. If a 33 MHz card shares a bus with a 66 MHz card, the faster card will downgrade to 33 MHz. All four of these slots support hot plug operations in HP UX. Hot plug is not supported with the Linux operating system.

All I/O slots are keyed for I/O cards with 3.3V signaling. Cards that use 5V signaling are not supported in the HP 900 rp4440.

I/O Card

J3525A

A6386A

A6749A

A6748A

DVD Read Only drive

The integrated multifunction I/O provides core I/O functionally and includes the management processor, which provides remote management and high availability monitoring capabilities.

• 10/100/1000Base-T LAN with two RJ 45 connectors -Supports LAN boot for operating system installation
  
• Two external LVD Ultra320 SCSI (320 MB/s) ports; Ultra320 is backward compatible with Ultra160, LVD Ultra2 and with SE SCSI-Order the appropriate cable to connect to external peripherals, example: VH to HD cable
  
• Two internal Ultra320 SCSI channels -One channel is routed to the external SCSI port and one channel is routed to the two internal hot plug disk bays
  
• An optional conversion kit is available to split the internal disks between two separate SCSI channels (HP product number A9740B). This option provides additional high availability through fault isolation on the internal disks.

• Dedicated 10/100Base-T LAN port for LAN console and embedded web console access
  
• DB-25 serial port-Multiplexed (using W cable) into three RS-232 ports: local ASCII console, remote/modem console, and general purpose
  
• Password protected console ports
  
• Console mirroring between all local, modem, LAN, and web consoles
  
• Remote power up and power down control
  
• Configurable remote access control
  
• Event notification to system console-Provides connectivity, information, and support for HP-UX tools (such as STM and EMS) to notify by email, pager and/or HP response centers.
  
• Interface to system monitoring and diagnostic hardware via an internal IC bus
  
• Secure Sockets Layer security on web console

The HP 9000 rp4440's integrated Management Processor provides four methods for console connections.

• SSL-secured Web console accessible through the 10/100Base-T management LAN
• Standard telnet connections accessible through the 10/100Base-T management LAN
• Local VT100 or hpterm terminal, or VT100 or hpterm emulator via local RS-232 serial connection
• Remote VT100 or hpterm terminal, or VT100 or hpterm emulator via external modem
• Keyboard and mouse connections are provided by USB.

The HP 9000 rp4440 provides a high level of integrated power protection:

• N+1 redundant hotswap power supplies
• N+1 redundant AC power input protection with electrical phase isolation
• Power monitoring and control

The HP 9000 rp4440 supports a second hot swap power supply for N+1 protection. One supply is shipped as a standard part of every system and is required for correct operation. The hot swap design allows for the online replacement of a power supply when N+1=2 supplies are configured in the server.

The HP 9000 rp4440 provides an independent power input receptacle for each power supply. The independent design provides protection against losing the connection from a power cord or breaker. The HP 9000 rp4440 power cords should always be plugged into separate breakers when possible.

The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.