• Operating System support: HP UX 11i version 1 and HP-UX 11i version 2 for HP 9000
• Dual channel Ultra160 SCSI controller, 2 internal disks on one channel, 1 internal disk on a second channel; second channel supports external devices as well.
  
• Internal and external Ultra160 SCSI port
  
• 10/100/1000Base-TX LAN (auto speed sensing, RJ-45 connector)
  
• iLO Manageability Card for remote management and HA monitoring
  
• Telnet and web console via 10/100Base TX management LAN (RJ-45 connector)*
  
• Three RS-232 serial ports linked to the management processor (multiplexed from a single DB-25 port)
  
• Factory integration of processors, memory, disk drives, removable media, and I/O cards
  
• Rackmountable into 19-inch cabinets
  
• Optional stand-alone pedestal mount
  
• One-year warranty with next business day on-site
  

• One PA-8900 800-MHz processor with 64 MB Level 2 cache: One core is activated on a two corel PA-8900 800-MHz processor module; a second core is activated by ordering optional part number A9770A.
  
• 1 GB PC2100 ECC Registered DDR266A SDRAM (2×256MB DIMMs)
  
• One power supply
  

• Two PA-8900 800-MHz cores (one two core PA 8900 processor module).
  
• 6 GB PC2100 ECC Registered DDR266A SDRAM (12×512MB DIMMs)
  
• Two Hotswap power supplies, providing N+1 protection for power supplies and power input
  
• Two PCI X/PCI IO adapter cards
  
• One internal DVD ROM or DVD+RW combo drive
  
• Three internal hot plug LVD SCSI disks

• Operating System support: HP-UX 11i version 1
• Dual channel Ultra160 SCSI controller, 2 internal disks on one channel, 1 internal disk on a second channel; second channel supports external devices as well.
  
• Internal and external Ultra160 SCSI port
  
• 10/100/1000Base-TX LAN (auto speed sensing, RJ-45 connector)
  
• iLO Manageability Card for remote management and HA monitoring
  
• Telnet and web console via 10/100Base TX management LAN (RJ-45 connector)*
  
• Three RS-232 serial ports linked to the management processor (multiplexed from a single DB-25 port)
  
• Factory integration of processors, memory, disk drives, removable media, and I/O cards
  
• Rackmountable into 19-inch cabinets
  
• Optional stand-alone pedestal mount
  
• One-year warranty with next business day on-site

• N+1 Hot swap cooling
  
• One Hot swap power supply standard-optional second hot swap power supply for N+1 protection
  
• On-line memory page deallocation
  
• ECC protected DDR memory
  
• Memory chip spare to overcome single DRAM chip failures
  
• Dynamic Processor resilience and deallocation
  
• UPS power management
  
• Hot Plug internal disks
  
• Two independent Ultra SCSI channels to internal disks for mirroring across disks and channels
  
• Journal file system for HP-UX
  
• Auto reboot
  
• HP MC/ServiceGuard for HP-UX
  
• HP ServiceGuard Extension for RAC for HP-UX
  
• ServiceGuard Manager for HP-UX
  
• Insight Manager 7-proactive fault management
  
• EMS HA Monitors for HP-UX
  
• ECM Toolkit for HP-UX
  
• HP Surestore AutoPath for HP-UX
  
• MirrorDisk for HP-UX

• Separate LAN for system management
  
• Password protection on console port
  
• Disablement of remote console ports
  
• SSL encryption on web console

• HP Ignite-UX for installation and deployment of the operating system
  
• HP Software Distributor-UX for software and patch management
  
• HP Servicecontrol Suite for HP-UX
  
• iLO Manageability Card for comprehensive remote management of HP-UX
  
• Process Resource Manager for HP-UX workload management

PA-8900 processor with two cores:

• 800-MHz
• Level 2 Cache: 64 MB (shared between cores)
• Level 1 Cache: 3 MB (1.5 MB per core)
• Single bit cache error correction
• 44 bit physical addressing
• 64 bit virtual addressing
• 4 GB maximum page size

The HP 9000 rp3410 supports DDR (double data rate) SyncDRAM (synchronous dynamic random access memory) DIMMs with ECC and chip spare protection. The HP 9000 rp3410 has twelve DIMM slots, allowing a maximum of 6 GB of total system memory.

• Memory is loaded in 512 MB¹, 1 GB or 2 GB options
  
• 512 MB option consists of 2 x 256 MB DIMMs, 1 GB option consists of 4×256 MB DIMMs, and 2 GB option consists of 4×512 MB DIMMs.
  
• Minimum memory is 1 GB. NOTE: 512 MB¹ (2×256 MB) is available for customers who have 512 MB installed (minimum memory was increased to 1 GB on July 12, 2004). A second pair of 256 MB DIMMs (512 MB option) must be added to achieve a quad before other memory is added. A third 256 MB DIMM pair is not supported.
  
• Maximum memory is 6 GB (12×512 MB DIMMs)
  
• Memory must be loaded in the specific order outlined on the system board.
  
• Memory is loaded across both memory buses (two DIMMs on each bus) to ensure maximum bandwidth and performance
  
• Total memory bandwidth is 8.5 GB/s, split across two 4.25 GB/s memory buses
  
• Open page memory latency is 80 nanoseconds

The HP 9000 rp3410 was designed for and has been tested in HP Standard Rack System/E Series cabinets and the HP Universal Rack G2 cabinets. HP cabinets are the best option for customers who want to ensure that their rack environment offers the utmost in safety, ease of service, factory integration, and HP field support. The HP cabinet family is made up of the following products:

HP System/E Series:

• A4900A-(25 EIA Units): up to 12 rp3410 servers
  
• A4901A-(33 EIA Units): up to 16 rp3410 servers
  
• A4902A-(41 EIA Units): up to 20 rp3410 servers
  

HP Universal Rack G2 Series:

• AF002A - (42 EIA Units): up to 20 rp3410 servers
  
• AF012A - (36 EIA Units): up to 16 rp3410 servers

Refer to the 10000 G2 Series Rack Best Practices Guide for information on rack deployment, stabilization and transportation. Go to HP.com/go/rackandpower for more information.

For factory integration, order racking product number AB241A in the HP 9000 rp3410 ordering guide

For customers who choose to use non HP cabinets, the HP 9000 rp3410 provides simple options for installation and HP field support. The HP 9000 rp3410 field rack kit contains adjustable slide rails, allowing the server to be mounted in cabinets that use the four post EIA mounting system.

Once the server is mounted in a non-HP cabinet, it must meet some simple criteria to ensure that HP field personnel can fully support the rack environment.

• Anti-Tip-The rack/cabinet must be solidly anchored to the floor both front and rear. This is usually accomplished by anti-tip feet or by direct bolting to the floor.
• Air Flow-The HP 9000 rp3410 uses front to back airflow to cool the unit. Thus a cabinet cannot have a solid front or rear door. Solid doors may have to be removed or changed to an open perforation pattern.
• Cable Strain Relief-A proper method of strain relief must be used. This may force the elimination of the rear door in some cases.
• Front and Rear Access-For proper cooling and ease of service access, HP recommends 32 inches of unobstructed floor space in the front and rear of rack installations. This recommendation applies to both HP and third-party racks and cabinets.

If a rack is not required, the system can be mounted vertically in the stand-alone pedestal mount (A6940A).

The HP 9000 rp3410 I/O architecture utilizes industry standard PCI-X and PCI buses in a unique design for maximum performance, scalability and reliability.

The HP 9000 rp3410 architecture uses seven high-speed I/O channels. Each channel provides 0.5 GB/s of sustained I/O throughput.

The two open PCI-X slots all have their own dedicated 64-bit 133-MHz PCI-X bus and their own independent I/O channel or channels. The independent channels provide improved I/O performance and error containment. Independence protects each I/O card from bus hangs or extended latencies due to the failure or high bandwidth demands of other I/O cards. Independence also ensures that each I/O card can achieve maximum throughput.

One PCI-X slot has two dedicated I/O channels, resulting in sustained PCI-X bandwidth of 1.0 GB/s. The second slot has one dedicated I/O channel, resulting in sustained PCI-X bandwidth of .5 GB/s.

All I/O slots are keyed for 3.3V I/O cards. 5V cards are not supported in the HP 9000 rp3410.

The remaining three I/O channels are allocated to the integrated core I/O.

I/O Card

J3525A

J3526A

2 /8

AD278A

A6749A

A6748A

DVD-ROM Drive Slim Line

The integrated multi function I/O provides core I/O functionally and includes the management processor, which provides remote management and high availability monitoring capabilities.

• 10/100/1000Base T LAN with RJ 45 connector-Supports LAN boot for operating system installation
  
• One external Ultra160 SCSI port-Note: the external SCSI port (SCSI channel B) can not be used if an internal drive is connected to the internal port of SCSI channel B
  
• Four USB 2.0 style A ports (USB 1.1 compatible)

• Dedicated 10/100Base-T LAN port for LAN console and embedded web console access
  
• DB-25 serial port-multiplexed (using W cable) into three RS-232 ports: local ASCII console, remote/modem console, and general purpose
  
• Password protected console ports
  
• Console mirroring between all local, modem, LAN, and web consoles
  
• Remote power up and power down control
  
• Configurable remote access control
  
• Event notification to system console-Provides connectivity, information, and support for HP-UX tools (such as STM and EMS) to notify by email, pager and/or HP response centers.
  
• Interface to system monitoring and diagnostic hardware via an internal IC bus
  
• Secure Sockets Layer security on web console

The HP 9000 rp3410's integrated Management Processor provides five methods for console connections.

• SSL-secured Web console accessible through the 10/100Base-T management LAN
• Standard telnet connections accessible through the 10/100Base-T management LAN
• Local VT100 or hpterm terminal, or VT100 or hpterm emulator via local RS-232 serial connection
• Remote VT100 or hpterm terminal, or VT100 or hpterm emulator via external modem

• The HP 9000 rp3410 supports up to three internal low profile hot-plug disk drives.
  
• Dual channel U160 SCSI provides independent channels for the internal disks-two disks on one channel (A) and one disk on a second channel (B). Split SCSI channels provide enhanced high availability-one channel can fail without impacting the disks on the other channel. Note: Each SCSI channel may be used for either internal or external connection but not both internal and external connections. SCSI channel B contains both an internal SCSI port and the external SCSI port. The external SCSI port can not be used if an internal drive is connected to the internal port of SCSI channel B. SCSI channel A only has an internal port.
  
• Supported by MirrorDisk/UX across disk drives and independent channels
  
• 36 GB 15K, 73 GB 15K, 146 GB 15K and 300 GB 15K hot plug Ultra320 SCSI disks are supported
  
• Optional optical media drives include a DVD ROM (A9919A), CD RW/DVD ROM combo drive (A9920A) and DVD+RW (AB348A).

The HP 9000 rp3410 provides a high level of integrated power protection.

• N+1 redundant hotswap power supplies (N=1)
• N+1 redundant AC power input protection with electrical phase isolation (N=1)
• Power monitoring and control
• The HP 9000 rp3410 supports up to two hot swap power supplies for N+1 protection. One supply is shipped as a standard component with every system. The second supply is optional.
• The HP 9000 rp3410 provides an independent power input receptacle for each power supply. The independent design provides protection against losing the connection from a power cord or breaker. The HP 9000 rp3410 power cords should always be plugged into separate breakers when possible.

The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.