HP 2 GB (4 x 512 MB) PC2-5300U DDR2-667 non-ECC

• 3 PCI slots (full-height, full-length)
• 1 PCI Express x16 slot (x4 functionality)
• 1 PCI Express x1 slot
• 1 PCI Express x16 graphics slot

• 2 internal 3.5" bays
• 1 external 3.5" bay, 3 external 5.25" bays*

NOTE: Third external 5.25" bay is not full depth in side orientation.

2 USB 2.0, 1 IEEE 1394 (requires optional PCI card to function), 1 audio out, and 1 microphone.

NOTE: Although HP Personal Workstations can be ordered with the HP Installer Kit for Linux and an IEEE 1394 card, HP cannot provide customer support for this configuration. Please refer to the Linux Hardware Support Matrix (http://www.hp.com/support/linux_hardware_matrix) for details, and to the Linux User Manual (http://www.hp.com/support/linux_user_manual) for tips on user-enablement of the IEEE 1394 Card.

xw4400X/XK1.86/
D80/K1.0/Xv/p
RB386UA#ABA

xw4400X/XK2.13/
F160/K2/FX56v/p
RB387UA#ABA

xw4400X/XK1.86/
F160/K1/Xv/p
RB388UA#ABA

xw4400X/XK2.4/
F250/K2.0/FX15y/p
RB389UA#ABA

xw4400X/XK2.67/
E160/K4.0/Xy/p
RB390UA#ABA

Memory (Unbuffered DIMMs)

Configurations less than 512 MB are not supported on either Microsoft Vista 32 or 64, configurations less than 1 GB are not supported on Microsoft Vista 64

PC2-5300E DDR2-667 or PC2-5300U DDR2-667DIMMS
Only unbuffered DDR2 DIMMs (ECC unbuffered or non-ECC) are supported and must be either x8 or x16 width. Memory upgrades are accomplished by adding DIMMs of the same or varied sizes. The Intel 975X chipset supports both PC2-5300 DDR2-667 non-ECC and ECC unbuffered memory.

For best performance the total amount and type of memory loaded into Channel A and Channel B should be the same. If it is not, your computer will see all the RAM installed but will run the memory controller at a lower performance mode. Although not required, for best performance add the memory in pairs rather than as a single DIMM (two 512 MB DIMMs will have better performance than a single 1 GB DIMM). Also, add the memory into both channels (e.g. one in socket 1 and one in socket 3) to take advantage of dual channel performance. If you have unused slots within a channel, make them socket 2 and socket 4. This provides the best margin for the memory bus. If you are only using 1 DIMM, install it in socket 1.

MAXIMUM MEMORY
Supports up to 8 GB DDR2-667 ECC Unbuffered or 2 GB DDR2-667 non-ECC SDRAM

8 GB (4 DIMM slots)

* Maximum memory capacities assume 64-bit operating systems, such as genuine Windows® XP Professional x64 Edition. Genuine Windows XP Professional (32-bit) supports up to 4 GB. 32-bit Linux supports up to 8 GB.

• RAID 0, 1, 5*, or 10* on a single array, up to 4 hard drives (*available 2007)
• Support for 1 or 2 RAID arrays on 4-ports for RAID 0 or 1
• RAID 1 spare and auto-rebuild
• Matrix RAID support
• AHCI support for NCQ drives
• 3.0Gb/s drive support

Integrated high definition digital audio with S/PDIF 6-channel pass-through, stereo microphone, and Yamaha XG Lite Softsynth support

NOTE: If using RHEL WS 3, the audio drivers are not included as part of the standard RHEL WS 3 operating system. Use the ALSA audio drivers included on the HP Driver CD or from the HP support website. See http://www.hp.com/support/linux_hardware_matrix and http://www.hp.com/support/linux_user_manual for details.

Monitors the temperature state within the chassis. Three modes:

• NORMAL - normal temperature ranges
• ALERTED - excessive temperatures are detected. Raises a flag so action can be taken to avoid shutdown or provide for a smoother system shutdown
• SHUTDOWN - excessive temperatures are encountered. Automatically shuts down the computer without warning before hardware component damage occurs

• System administrators can power on, restart, and power off a client computer from a remote location.

• Allows the system to enter and resume from low power modes (sleep states)
• Controls system power consumption, making it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system
• Supports ACPI 2.0 for full compatibility with 64-bit operating systems

• Allows management SW to read revision level of the system board
• Revision level is digitally encoded into the HW and cannot be modified

• System administrators can power on, restart, and power off a client computer from a remote location.
• Enables cost-effective power consumption when the administrator needs to distribute software, perform security management, or update the ROM.

• Enhanced Disk Drive Specification Version 1.1
• BIOS Enhanced Disk Drive Specification Version 3.0

• PCI Local Bus Specification, Revision 2.3
• PCI Power Management Specification, Revision 1.1
• PCI Firmware Specification, Revision 3.0, Draft .7

• Serial ATA Specification, Revision 1.0a
• Serial ATA 3 Gb/s: Extensions to Serial ATA 1.5 Gb/s, Revision 1.0

The first client management product line consists of HP OpenView Configuration Management Solutions and HP OpenView Client Configuration Manager.

The second client management product line is comprised of the HP Client Premium Suite, HP Client Foundation Suite, and HP Client Manager

To learn more about all of these solutions, visit http://www.hp.com/go/easydeploy

HP Client Manager is available for free for use with all HP business PCs, Notebooks, and Workstations. It enables central tracking, monitoring, and management of the hardware aspects of HP client systems:

• Get valuable hardware inventory information such as CPU, memory, video, and security settings
• Monitor system health to fix problems before they occur
• Install drivers and BIOS updates without visiting each PC
• Remotely configure BIOS and security settings
• Automate processes to quickly resolve hardware problems
  

Additional Altiris solutions (fee-based) are available to address Workstation management challenges through the entire IT lifecycle including:

• Inventory assessment
• Software license compliance
• Personality migration
• Software image deployment
• Software distribution
• Asset management
• Problem resolution

Visit http://www.hp.com/go/clientmanager for more information, to download HP Client Manager, and to evaluate the Altiris solutions

• Repository for storing company-specific property asset numbers for easy tracking
• Initially set equal to the system serial number
• Stored in a protected section of non-volatile memory that can be accessed and modified with the F10 Setup program

A feature of SATA and SCSI, Cyclic Redundancy Checking provides data transfer verification and proactive notification of hard drive data transmission problems with recommendations for enhancing system performance. It detects all the following errors' types:

• single-bit errors
• double-bit errors
• an odd number of errors
• error bursts up to 32-bits long

• Drive Protection System (Adaptec and LSI SCSI controllers do not offer DPS)
• A diagnostic hard drive self test. It scans critical physical components and every sector of the hard drive for physical faults and then reports any faults to the user.
• Running independently of the operating system, it can be accessed through the computer's setup procedure. It produces an evaluation on whether the hard drive is the source of the problem and needs to be replaced.

The system expands on the Self-Monitoring, Analysis, and Reporting Technology (SMART), a continuously running systems diagnostic that alerts the user to certain types of failures
DPS Access through F10 Setup during Boot (F10 diagnostic access not available with SCSI drives)

• Program to proactively communicate Product Change Notifications (PCNs) and Customer Advisories by email to customers, based on a user-defined profile.
• PCNs provide advance notification of hardware and software changes to be implemented in the factory providing time to plan for transition.
• Customer Advisories provide concise, effective problem resolution, greatly reducing the need to call technical support.

• System administrators can power on, restart, and power off a client computer from a remote location.
• Enables cost-effective power consumption when the administrator needs to distribute software, perform security management, or update the ROM.

Advanced Configuration and Power Management Interface (ACPI).

• Allows the system to wake from a low power mode.
• Controls system power consumption, making it possible to place individual cards and peripherals in a low-power or powered-off state without affecting other elements of the system

Dual Color Power and HD LED on Front of Computer (Indicates Normal Operations and Fault Conditions)

System/Emergency ROM Flash Recovery
with Video

Configuration Record SW

Over-Temp Warning on Screen (Requires IM Agents)

Restore CD set

Flash ROM

3.3V Aux Power LED on System PCA

Dual Function 5V Aux Power LED (ON)/PS_ON LED (OFF) on System PCA

Diagnostic Power Switch LED on board

Clear Password Jumper

Clear CMOS Button

CMOS Battery Holder for easy Replacement

Processor ZIF Socket for easy Upgrade

DIMM Connectors for easy Upgrade

NIC LEDs (integrated) (Green & Amber)

ASF 1.0 support (Alert Standard Format)

Dual Function Front Power Switch

This product has received or is in the process of being certified to the following approvals and may be labeled with one or more of these marks:

• US Federal Energy Management Program (FEMP)
• China Energy Conservation Program
• IT ECO declaration
• Japan PC Green label*

* This product conforms to the examination standards (2003 version) under JEITA's 'PC Green Label System.'

• Intel LGA775 processor socket
• 4 USB ports
• 3 PCI slots and 3 PCI Express slots
• 5 storage bays
• 4 memory slots

This product complies with ISO standards:

• EU Directive 91/ 157/ EEC
• EU Directive 93/ 86/ EEC
• EU Directive 98/ 101/ EEC

Batteries used in the product do not contain:

• Mercury greater the 5ppm by weight
• Cadmium greater than 10ppm by weight
• Lead greater than 4000ppm by weight.

Battery size: CR2032 (coin cell)
Battery type: Lithium

• This product is in compliance with the Restrictions of Hazardous Substances (RoHS) directive - 2002/95/EC.
• This HP product is designed to comply with the Waste Electrical and Electronic Equipment (WEEE) Directive – 2002/96/EC.
• Plastics parts weighing over 25 grams used in the product are marked per ISO 11469 and ISO1043.
• This product contains 0% recycled materials (by wt.)
• This product is >90% recycle-able when properly disposed of at end of life.

This product does not contain any of the following substances in excess of regulatory limits (refer to the HP General Specification for the
Environment at http://www.hp.com/hpinfo/globalcitizenship/environment/supplychain/gen_specifications.html):

• Asbestos
• Certain Azo Colorants
• Certain Brominated Flame Retardants – may not be used as flame retardants in plastics
• Cadmium
• Chlorinated Hydrocarbons
• Chlorinated Paraffins
• Formaldehyde
• Halogenated Diphenyl Methanes
• Lead carbonates and sulfates
• Lead and Lead compounds
• Mercuric Oxide Batteries
• Nickel - finishes must not be used on the external surface designed to be frequently handled or carried by the user.
• Ozone Depleting Substances
• Polybrominated Biphenyls (PBBs)
• Polybrominated Diphenyl Ethers (PBBEs)
• Polybrominated Biphenyl Oxides (PBBOs)
• Polychlorinated Biphenyl (PCB)
• Polychlorinated Terphenyls (PCT)
• Polyvinyl Chloride (PVC) – except for wires and cables, and certain retail packaging has been voluntarily removed from most applications.
• Radioactive Substances
• Tributyl Tinches; TBT), Triphenyl Tinches; TPT), Tributyl Tin Oxide (TBTO)

HP follows these guidelines to decrease the environmental impact of product packaging:

• Eliminate the use of heavy metals such as lead, chromium, mercury and cadmium in packaging materials.
• Eliminate the use of ozone-depleting substances (ODS) in packaging materials.
• Design packaging materials for ease of disassembly.
• Maximize the use of post-consumer recycled content materials in packaging materials.
• Use readily recyclable packaging materials such as paper and corrugated materials.
• Reduce size and weight of packages to improve transportation fuel efficiency.
• Plastic packaging materials are marked according to ISO 11469 and DIN 6120 standards.

Signal-to-Noise Ratio (20kHz Low-pass filter, A-Weighted)

• Stereo Output: 109dB
• Front and Rear Channels: 109dB
• Center, Subwoofer and Side Channels: 109dB

160 GB
(7,200 rpm)